Difference between revisions of "Signal Reader Assignment Wizard"

From WICE Wiki v2.89
Jump to navigation Jump to search
(Finished recorder properties)
(Moved to Signal Reader Assignment Editor)
 
(21 intermediate revisions by 3 users not shown)
Line 1: Line 1:
[[File:Choose Signal Source.png|thumb|Figure 1: Choosing a signal source|375x375px]]The Signal Reader Assignment Wizard can be found under the tab '''Assignment''' and allows the user to create new assignments for signal reader directly on the portal. This page will guide you through the basics of using the wizard.
<includeonly>=Assignment Tab=</includeonly>
=== Choosing a Signal Source ===
First, you must select a signal source to base your new assignment on. Today, only custom vehicle types can be used for this, see Figure 1. If you would like to edit the Custom Vehicle types or create a new one, this can be done by admins under the administration tab.


When you feel comfortable with which signal source you would like to use, double click it or select it and click '''Create new assignment'''.
This page has been moved [[Signal Reader Assignment Editor|here]].
 
=== Creating a new assignment ===
Now that you have chosen a signal source, you can start creating the assignment. The first tab that you are presented with is the '''Assignment global settings''' tab where you can add information about the assignment so that you can easily keep track of what this assignment is about. Creator and creation date are both automatically filled in and cannot be changed because of consistency.
 
Under the '''Measurements''' tab, see Figure 2, you are faced with a table of Measurement Setups and an information window. These measurement setups are the core of a signal reader assignment. They contain '''Triggers''' that activate and deactivate on certain conditions provided by the user. Each trigger can contain a '''Recorder''' that contains a list of certain signals that will be measured when the start condition for the respective trigger is met. A trigger can also be used to act as a '''setup switch'''.
 
==== Trigger ====
To add a trigger to a measurement setup, click the '''Add trigger''' button for the respective measurement setup. This will create a new Trigger in the trigger table in the respective measurement setup and the information window will be filled with new settings for this trigger for you to add.
 
Fill out the '''start trigger''' '''condition''' for the trigger. This is easiest to do in the '''Edit expression''' window that you can get to by clicking one of the '''Edit''' buttons. To find a new signal to add a condition for, use the '''Add signal''' button. Here, you can browse all signals available for this assignment. Use the dropdown to browse signals from different can-busses and Wice generic internal signals. If you want to browse the signals currently in use in the assignment for the selected signal source, check the '''Search in assignment''' box. If you want more information about a signal, select it and click '''More info'''. When you have found the signal you want, double click it or select it and click '''Add signal'''. Now you can use the '''Operators''' list to add a condition for the signal, for example " > 0". When you are satisfied with the start condition, click Save to save the expression.
 
A '''stop trigger condition''' is not required, but can be supplied to determine when the recording should stop. If the stop condition is not supplied, the settings for the recorder will tell when the recording should stop.
 
You can use the '''trigger''' '''Setup switch''' to switch to/run a measurement setup when the start condition is met. Keep in mind though, that the setup switch will not run until all currently started recorders have at least fulfilled their '''minimum duration'''. A trigger with a recorder cannot have a setup switch, but the recorder can.
 
==== Recorder ====
By selecting the tab Recorder you can '''add a recorder''' to the trigger. This will populate the information window with settings for this recorder, starting with the signals to be recorded.
 
===== Signals =====
Click the '''Add Signal''' button to open a window to add signals for recording. This window is much like the window for adding signals for the trigger, only differing in the fact that you can select multiple signals in this window. The selected signals for this recorder are shown in the right table, see Figure 3. To add new signals to this table, you can either:
* Double click the signal,
* Drag and drop the signal 
* Select the signal and click the right pointing arrow
Click the red symbol to the right of each signal to remove it. When you are done, click Ok to add the signals. 
 
Now that you have added some signals, you can give them each a '''Skip factor''', default 1, which is an integer that determines how often the signal should be recorded/stored when supplied. For example, a skip factor of 1 will record the signal every time it is supplied and a skip factor of 3 will record the signal every third sample.
 
===== Properties =====
Under the recorder tab '''Properties''' you can select the properties for the recorder.
 
'''Number of shots''' is an important factor for a recorder. A '''shot''' is the term used for a single recording and number of shots is therefore the number of times we should record. A shot is only started when the start trigger condition is met and will continue until any of these events occur:
* The recording fulfills the maximum duration.
* The recording fulfills the minimum duration and the '''stop trigger condition''' is met.
* The recording fulfills the minimum duration and a trigger start a '''setup switch'''.
* The recording fulfills the minimum duration and another recorder starts a '''setup switch'''.
* A setup switch is started manually.
* The assignment is stopped manually.
The '''recorder Setup switch''' is started when recorder has performed its number of shots and all other started recorders have at least fulfilled their minimum duration. It is, like the trigger setup switch, used to switch to/run a measurement setup.
 
You can also select the '''Pre trigg duration''' which determines the amount of data that will be saved in the flash before the start trigger condition is met. Range is 0 to 4294967295 (2<sup>32</sup>).
 
The '''Post trigg duration''' is much like the pre trigg duration and determines the amount of data that will be saved after the stop trigger condition is met. Range is 0 to 4294967295 (2<sup>32</sup>).
 
The '''Minimum duration''' determines the minimum amount of data that needs to be recorded before it becomes possible to cancel the recording through either a stop trigger or a setup swtich started by a trigger or another recorder.
 
The '''Maximum duration''' determines, as the name suggest, the maximum amount of data that should be recorded. Range is 0 to 4294967295 (2<sup>32</sup>).
 
The '''Unit''' for the four aforementioned durations can be set to seconds, samples or bytes. If you choose to set them to seconds, the device will use the timestamps of the incoming data to determine the four aforementioned durations.
 
=== Editing an assignment ===

Latest revision as of 15:12, 5 May 2021


This page has been moved here.

Retrieved from "https://wiki.alkit.se/wice289/index.php?title=Signal_Reader_Assignment_Wizard&oldid=2554"